Knowing Essential Plumbing Skills is Crucial For Installing a Bathtub
Knowing Essential Plumbing Skills is Crucial For Installing a Bathtub
Blog Article
Nearly everybody is bound to have their own piece of advice about How to Install a Bathtub.
Setting up a bathtub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a moderately difficult job. If the old tub is readily accessible, the project can relocate speedily; if you have to open up a wall surface to eliminate the old tub and place the brand-new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to leave the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the task and also are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed job, it is better to think about utilizing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have currently purchased a brand-new tub and also don't require to change the setup of your previous water pipes.
Your tools and product list must consist of the following:
Getting ready for the Setup
Firstly, the sustaining frame supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Using the two wooden boards under its feet, put the tub in the called for setting. The wood boards are handy in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub till the level reviews level.
To mount taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the supply of water as well as check all joints and also new pipework for leakages as well as tighten them if needed. Fill up the tub as well as likewise check the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has been made use of at least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers are in location in between the faucet as well as the sink. Protect the tap in place with the supplier offered backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous kind needs to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to split a stiff seal, creating the water to pass through the wall in between the bath as well as the tiling, resulting in difficulties with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can fracture rather early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub Yourself? Create a remark directly below. We would be glad to see your feelings about this entry. We hope that you come back again in the near future. Liked our content? Please share it. Let somebody else find it. We thank you for reading our article about Tools You Need to Install a New Bathtub .
Immediate relief? Contact. Report this page